Skip to main content
Version: 3.1 (New Interface)

Set up Web to Call

You set up Web to Call once for your account, in the Admin Panel. The widget you create here also registers the website that calls are allowed from.

There are four steps:

  1. Open Click to Call.
  2. Initialize the connection.
  3. Create the widget.
  4. Get the embed code.
Do the steps in order

The connection must exist before calls can reach your contact center, so initialize it before you create the widget.

Before you start​

  • Web to Call is licensed for your account. If you aren't sure, ask Intellicon Support.
  • Your user role has permission to add, edit and delete in Click to Call.
  • You know the exact website address the calls will come from, for example www.example.com.
  • An Intelli Flow is ready for web calls. It answers the call and sends it to a queue. Every web call goes through this flow.
  • The queue has agents assigned who are signed in and ready to take calls.

Step 1: Open Click to Call​

  1. In Intellicon, go to Settings (the Admin Panel).
  2. Click the Click to Call card.

The WebRTC Widget page opens and shows two lists:

  • WebRTC Widget Configurations: your widget. It's empty until you create one.
  • WebRTC Widget Trunk: the connection between your contact center and the Web to Call service. It carries all web calls.
Don't see the Click to Call card?

The module is turned off for your instance, or Web to Call isn't licensed. Contact Intellicon Support or your Implementation team.

Step 2: Initialize the connection​

  1. In WebRTC Widget Trunk, click Initialize Trunk +. The button only appears when there's no connection yet.
  2. Wait for Widget trunk initialized successfully. The connection appears in the list.

You only do this once. Leave the connection as it is unless Intellicon Support asks you to change it.

Re-register appears next to the connection. Click it if calls stop reaching your contact center, or if Intellicon Support asks you to. You see Trunk credentials updated, re-registration queued.

The WebRTC Widget page with an empty widget list and an Initialize Trunk button above an empty trunk list
Before the connection is initialized

Step 3: Create the widget​

The Add New WebRTC Widget form: Basic Information, Call-to-Action Settings and the Widget Preview with a green call button and an orange Call Now for Free! message
The Add New WebRTC Widget form with the Widget Preview
  1. In WebRTC Widget Configurations, click Add New +. The Add New WebRTC Widget form opens.
  2. Enter a Widget Name, 3 to 100 characters. Visitors don't see it.
  3. Enter the Website Domain exactly as it appears in the browser's address bar, for example www.example.com. Calls only work from this website.
  4. In Intelliflow IVRs, choose the Intelli Flow that answers web calls.
  5. Choose which pre-call fields are required, and set the appearance and messages. Most fields already have a working value. The Widget Preview on the right shows the button and message as you change them. Widget settings describes every field.
  6. Click Create Widget. You see Widget successfully added.

The widget appears in the list with its ID, Name, Widget Type, SIP Domain, Website, Intelliflow and Last Updated time. Add New + is replaced by One widget is allowed only, because each account has one widget.

Enter the Website Domain

The form shows Website Domain as optional, but calls only connect from a website that's registered here. example.com and www.example.com are different websites, so enter the one your site uses.

New widgets start as Popup

A new widget is saved with the Popup Widget type. To use the Embedded Widget type, create the widget first, then click Action > Edit, choose Embedded Widget and click Update Widget.

If Widget Name or Intelliflow IVRs is empty, the form shows This field is required. under the field and doesn't save.

Step 4: Get the embed code​

  1. On the widget, click Action > Get Code. The Widget Embed Code window opens. On the Edit form, you can also click View Embed Code.
  2. Click Copy to Clipboard.
  3. Give the code to whoever manages your website. To add it, see Add the widget to a website.

Paste the code exactly as it is. Your settings are saved inside it.

The widget list with one widget and its Action menu open, showing Get Code, Edit and Delete
The widget's Action menu
Make a test call

After you create the widget or change the Website Domain, make a test call from your website to confirm it works. See Test the widget.

Change, pause or delete the widget​

  • To change it: click Action > Edit, change the settings and click Update Widget.
  • To stop calls without deleting it: clear the Website Domain and click Update Widget. The website is switched off for calls.
  • To delete it: click Action > Delete, then confirm. Calls from the website stop, and you can create a new widget.
Copy the code again after every change

Your settings are part of the embed code. After you click Update Widget, copy the code again with Get Code and replace the old code on your website. Until you do, your website keeps the old settings.